Exploring Plumbing Fundamentals When You Install a Bathtub
Exploring Plumbing Fundamentals When You Install a Bathtub
Blog Article
Just about every person has got their private assumption on the subject of How to Install a Bathtub.
Installing a bath tub isn't precisely rocket science, but it does call for solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably challenging task. If the old tub is easily accessible, the job can relocate quickly; if you have to open up a wall surface to remove the old bathtub and also position the new bath tub, the job is a lot harder. In either instance, the task is within a home handyman's skills, although you will need a helper to move out the old tub and set in the new one. Make sure you have qualified yourself for the job and fit trying it. Instead of employing a service provider to take control of a halfway-completed project, it is better to consider using one prior to you start. Opportunities are you might need a professional plumber to make tube connections.
This write-up will aid you set up a new bathtub in your washroom if you have currently purchased a new bathtub and also do not need to change the setup of your previous supply of water pipelines.
Your tools as well as material list should consist of the following:
Removing Old Touches
If you need to replace old taps with new ones as a part of your setup, after that the first thing you must do is detach the water system. After doing so, activate the taps to drain pipes any water continuing to be in the system. The procedure of removing the existing faucets can be fairly problematic because of the limited access that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have been eliminated, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from transforming throughout this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing compound.
Prior to carrying on to fit the new faucets, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the tap and the various other end supplies a link to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly require lowering couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the tap in the placing opening in the bath/basin making sure that the washing machines remain in location in between the faucet and also the sink. Protect the tap in place with the maker given backnut. Once the faucet is safely in position, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal tap connectors. The former kind needs to be connected to the tap ends initially, tightening up just by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Setting up the Bath tub
Using the two wooden boards under its feet, position the tub in the needed setting. The wooden boards are useful in evenly spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 small factors.
The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the spirit level as well as adjusting the feet on the tub till the spirit level checks out degree.
To install taps, fit all-time low of the furthest versatile faucet port to the suitable supply pipeline by making a compression join; then do the same for the other faucet.
Activate the water supply and check all joints as well as new pipework for leaks as well as tighten them if required. Fill up the tub and likewise inspect the overflow outlet and the normal electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as explained in the producer's instruction manual. Tiling and also sealing around the bath tub needs to wait until the bathtub has been used at least when as this will resolve it into its final setting.
Planning for the Installment
Firstly, the supporting framework supplied with the bath ought to be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is important to see to it that if the tap comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the taps unit to avoid pressure on the bath tub.
Fit the adaptable tap ports to the bottom of both faucets utilizing 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you make use of every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should now prepare to be suited its last placement.
Tiling Around the Bathtub
In the location where the bath meets the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to break a stiff seal, causing the water to pass through the wall in between the bath and also the tiling, resulting in difficulties with dampness as well as feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealers to assimilate your fixtures and installations. They are marketed in tubes and cartridges, and are capable of securing gaps up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of drenched paper or soft rope. Remember to constantly fill the tub with water prior to securing, to allow for the movement experienced when the tub remains in usage. The sealant can break rather very early if you do not take into consideration this motion before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also conveniently offered on the marketplace. It is a good idea to fit the tiles utilizing water-resistant or waterproof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been brought to that article about How to Install a Bathtub from a friend on another web property. Enjoyed our review? Please share it. Help somebody else locate it. Thanks for taking the time to read it.
Top plumbers, one call. Report this page